Lesson 20 74HC595

Share for us

Introduction

Generally, there are two ways to drive a single 7-segment display. One way is to connect its 8 pins directly to eight ports on the Uno board, which we have done previously. Or you can connect the 74HC595 to three ports of the UNO board and then the 7-segment display to the 74HC595. In this experiment, we will use the latter. By this way, we can save five ports – considering the Uno board’s limited ports, this is very important. Now let’s get started!

Components

Components Introduction

74HC595

The 74HC595 consists of an 8−bit shift register and a storage register with three−state parallel outputs. It converts serial input into parallel output so you can save IO ports of an MCU.

When MR (pin10) is high level and OE (pin13) is low level, data is input in the rising edge of SHcp and goes to the memory register through the rising edge of SHcp. If the two clocks are connected together, the shift register is always one pulse earlier than the memory register. There is a serial shift input pin (Ds), a serial output pin (Q) and an asynchronous reset button (low level) in the memory register. The memory register outputs a Bus with a parallel 8-bit and in three states. When OE is enabled (low level), the data in memory register is output to the bus.

Pins of 74HC595 and Their Functions

Q0-Q7: 8-bit parallel data output pins, able to control 8 LEDs or 8 pins of 7-segment display directly.

Q7’: Series output pin, connected to DS of another 74HC595 to connect multiple 74HC595s in series.

MR: Reset pin, active at low level.

SHcp: Time sequence input of shift register. On the rising edge, the data in shift register moves successively one bit, i.e. data in Q1 moves to Q2, and so forth. While on the falling edge, the data in shift register remain unchanged.

STcp: Time sequence input of storage register. On the rising edge, data in the shift register moves into memory register.

OE: Output enable pin, active at low level.

DS: Serial data input pin

VCC: Positive supply voltage

GND: Ground

Schematic Diagram

In the experiment MR (pin10) is connected to 5V (HIGH Level) and OE (pin 13) to GND (LOW Level). Therefore, the data is input into the rising edge of SHcp and enters the memory register through the rising edge. We use the shiftout() function to output a 8-bit data to the shift register through DS. In the rising edge of the SHcp, the data in the shift register moves successively one bit in one time, i.e. data in Q1 moves to Q2, and so forth. In the rising edge of STcp, data in the shift register moves into the memory register. All data will be moved to the memory register after 8 times. Then the data in the memory register is output to the bus (Q0-Q7). So the 16 characters are displayed in the 7-segment in turn.

Experimental Procedures

Step 1: Build the circuit (pay attention to the direction of the chip by the concave on it)

7-Segment74HC595Uno Kit
aQ7 
bQ6 
cQ5 
dQ4 
eQ3 
fQ2 
gQ1 
DPQ0 
 VCC5V
 DS11
 CEGND
 ST12
 SH8
 MR5V
 Q7’N/C
 GNDGND
 GND

Step 2: Open the code file. 

Step 3: Select the Board and Port.

Step 4: Upload the sketch to the board.

You should now see the 7-segment display from 0 to 9 and A to F.

Code Analysis

Code Analysis 20-1  Set the array elements

int datArray[16] = {252, 96, 218, 242, 102, 182, 190, 224, 254, 246, 238, 62, 156, 122, 158, 142};

This array stores the data of the 16 characters from 0 to F. 252 stands for 0, which you can calculate by yourself. To display 0, the segment g (the middle one) of the 7-segment display must be low level (dim).

Since the segment g is connected to Q1 of the 74HC595, set both Q1 and DP (the dot) as low level and leave the rest pins as high level. Therefore, the values of Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 are 1 1 1 1 1 1 0 0.

Change the binary numbers into decimal ones: 1×27+1×26+1×25+1×24+1×23+1×22+0x21+1×20=252.

So that’s the value for the number 0 to be displayed. You can calculate other characters similarly.

Code Analysis 20-2  Display 0-F in the 7-segment display

for(int num = 0; num < 16; num++)

  {

    digitalWrite(STcp,LOW); //ground ST_CP and hold low for as long as you are transmitting

    shiftOut(DS,SHcp,MSBFIRST,datArray[num]);

    //return the latch pin high to signal chip that it

    //no longer needs to listen for information

    digitalWrite(STcp,HIGH); //pull the ST_CPST_CP to save the data

    delay(1000); //wait for a second

  }

Set STcp as low level first and then high level. It will generate a rising edge pulse of STcp.

shiftOut() is used to shift out a byte of data one bit at a time, which means to shift a byte of data in dataArray[num] to the shifting register with the DS pin. MSBFIRST means to move from high bits.

After digitalWrite(STcp,HIGH) is run, the STcp will be at the rising edge. At this time, the data in the shift register will be moved to the memory register.

A byte of data will be transferred into the memory register after 8 times. Then the data of memory register is output to the bus (Q0-Q7). You will see a character is displayed on the 7-segment. Then delay for 1000ms. After that line, go back to for(). The loop repeats until all the characters are displayed in the 7-segment display one by one after 16 times.