Lesson 26 DS18B20 Temperature Sensor

Share for us
Share on facebook
Share on twitter
Share on pinterest
Share on whatsapp

Introduction

Temperature Sensor DS18B20 is a commonly used digital temperature sensor featured with small size, low-cost hardware, strong anti-interference capability and high precision. The digital temperature sensor is easy to wire and can be applied a various occasions after packaging. Different from conventional AD collection temperature sensors, it uses a 1-wire bus and can directly output temperature data.

Required Components

 1 * Raspberry Pi

– 1 * Breadboard

– 1 * DS18B20 Temperature Sensor module

– 1 * 3-Pin anti-reverse cable 

Experimental Principle

With a unique single-wire interface, DS18B20 requires only one pin for a two-way communication with a microprocessor. It supports multi-point networking to measure multi-point temperatures. Eight sensors can be connected at most, because it will consume too much power supply and cause low voltage thus harming the stability of transmission.

When using the DS18B20, you need to connect a 10KΩ resistor to the middle pin DQ to pull up the level. The schematic diagram of the module is as shown below:

Experimental Procedures

Step 1: Build the circuit according to the following method. 

Raspberry PiGPIO Extension BoardDS18B20 Temperature Sensor
GPIO7GPIO4SIG
3.3V3V3VCC
GNDGNDGND

Step 2:Upgrade your kernel.

sudo apt-get update
sudo apt-get upgrade

Step 3:You can edit that file with nano.

sudo nano /boot/config.txt 

Then scroll to the bottom and type. 

dtoverlay=w1-gpio

Then reboot with

sudo reboot 

Mount the device drivers and confirm whether the device is effective or not.

sudo modprobe w1-gpio
sudo modprobe w1-therm
cd /sys/bus/w1/devices/
ls

The result is as follows:

root@rasberrypi:/sys/bus/w1/devices# ls
28-00000495db35 w1_bus_master1

28-00000495db35 is an external temperature sensor device, but it may vary with every client. This is the serial number of your ds18b20.

Step 4:Check the current temperature.

cd 28-00000495db35
ls

The result is as follows:

root@rasberrypi:/sys/bus/w1/devices/28-00000495db35# ls
driver  id  name    power   subsystem   uevent  w1_slave
cat w1_slave

The result is as follows:

root@raspberrypi:/sys/bus/w1_slave/28-00000495db35# cat w1_slave
a3 01 4b 46 7f ff 0d 10 ce : crc=ce YES
a3 01 4b 46 7f ff 0d 10 ce t=26187

The second line t=26187 is current temperature value. If you want to convert it to degree Celsius, you can divide by 1000, that is, the current temperature is 26187/1000=26.187 ℃.

For C Users:

Step 2: Change directory and edit.

cd /home/pi/SunFounder_SensorKit_for_RPi2/C/26_ds18b20/
nano ds18b20.c

Find the following line, replace “2800000495db35″ with your sensor address. Save and exit.

char* addr = "/sys/bus/w1/devices/28-00000495db35/w1_slave";

Step 6: Compile.

gcc ds18b20.c -lwiringPi

Step 7: Run.

sudo ./a.out

For Python Users:

Step 5: Change directory and edit.

cd /home/pi/SunFounder_SensorKit_for_RPi2/Python/
nano 26_ds18b20.py

Step 6: Run.

sudo python3 26_ds18b20.py

Now, you can see the current temperature value displayed on the screen.